Frequent Asked Questions - FAQ's

In this section we have attempted to answer the most frequently asked questions (FAQs) about Der Rampen Shop world, how does it work? What will I get? How to use the products? How to select the correct item? and much more, all you need scroll down the page and find the required product category, or simple click on the product category on the displayed table. Alternately please contact us.

Plant Ramps FAQ's

How long should the ramp be?

For plant ramps Health & Safety  we recommend that no gradient greater than 30% (16.5 degrees) should be used. Furthermore, no TUV Certified Ramp is designed to exceed this gradient. To calculate your gradient simply measure the height from ground level to the loading deck & multiply this by 3.3 to give the optimum length of ramp.

Plant Ramp Length Calculation

Do the ramps have a minimum load height?

We don’t advise to use the ramps lower than 100mm of the stated max load height as they will not sit flat on the ground. For example, if the ramp has a max load height of 900mm do not use lower than 800mm.

For custom solutions, please contact our ramp specialists

Can the ramps be used over the max load height?

No, the ramp will be too steep. Using the ramp above it’s recommended load height may cause accident, injury or death and will invalidate the warranty.

Should I allow extra capacity in the ramps for safety?

Our ramps are manufacturer and engineered to European TUV standards, which require us to build in a 200% safety. When calculating which capacity you require you must factor in the weight of the machine, the load if any, the operator, fuel/oil and attachments along with the wheelbase. Please note the wheelbase can affect the capacity which the ramp can hold, please view the details tab under the product to see the capacity of the ramp based on wheelbase. Please note if you exceed the stated capacity the warranty is invalidated.

How durable are aluminium ramps compared to steel?

If the ramps are used sensibly, there is no reason why aluminium ramps should not last as long as steel, and much longer than steel ramps with wooden inserts.

Can I load steel tracked equipment?

Der Rampen Shop has a number of vehicle ramps and plant ramps that are available with a rubber coated surface or milled surface that allows the harder steel tracks to be used on aluminium ramps. The usual vehicle and plant ramps are NOT suitable for solid wheeled machinery.

What is the minimum track width?

The narrowest the tyre/track of the vehicle can be on the surface of the ramp. This is to make sure the weight is spread across the surface to improve the life expectancy of the ramp.

When in use, how do I secure the ramps to my vehicle?

Safety is The primary concern and Der Rampen Shop can provide a number of very secure connection options to suit your vehicle, it is really up to you. Many of our ramps are supplied with our movable safety devices that slide in the aluminium extrusion under the loading lip. This device should be placed between the lorry bed and the tailgate. Once this is in place the ramps will not shift during loading. Another option is to use the drop bolts supplied. The loading lips of the ramps are pre-drilled to accommodate the bolts. Our low loader ramps have underside tie bars for attaching a chain or strap. Our connection options can be viewed here, the standard connection provided is a rest on connection, for alternative connection types the fee is 77,35€ inc. VAT

Do the ramps have safety edges?

All products are built flat top/no edges unless specified that edges are required. Products built with edges are production orders and therefore a longer lead time. The edges also decrease the usable width.

What if I need a specific length or width?

Der Rampen Shop can manufacture vehicle ramps to specific needs, please contact a sales advisor for a quotation

Can Der Rampen Shop manufacture special applications/do custom builds?

A. Der Rampen Shop manufacture a wide range of aluminium and steel extrusions and have been able to solve many unusual loading problems. Previous projects include purpose made plant ramps for drilling rigs, custom built truck ramps, ramps for unloading barges, vehicle ramps for the ministry of defence and the oil industry along with many specialist plant ramps and car ramps. We can also manufacture bespoke ramps for wheelchairs and disabled access. Modifications undertaken by anyone other than Der Rampen Shop invalidate the warranty.

Can I load a forklift on a plant ramp?

Not without first double checking with an advisor before purchasing. Forklifts are not designed to operate on inclines which means they need a very long ramp. They also have solid wheels which can damage the ramp surface so often we have to supply a reinforced model from our factory. 

Can I use a winch to assist loading equipment?

Winches fundamentally alter the normal weight distribution when loading machines and equipment. Stated weight limits are dramatically reduced when using a winch. Winches can be used but great care and attention must be taken, please speak with our sales advisers for help specifying ramps. The most important thing is to keep the rope of winch parallel with the ramp. If you intend to use a winch please make this clear to your sales adviser before purchasing.

Product Dimensions – please note that due to manufacturing techniques and processes all dimensions of products may vary by up to 2% plus or minus of the dimensions shown on the website. The only exception to this is ramp length of our vehicle ramps and loading ramp range – the lengths shown may vary by up to 5% depending upon the connection chosen. If you require a specific length please do let us know and we can advise accordingly.

plant ramps and loading rampsplant ramps and loading ramps

Car Ramps FAQ's

Are prices/capacities listed for a single ramp?

All prices/capacities listed on our site are for a pair of ramps unless otherwise specified.

How long do my ramps need to be?

The vertical height you are loading up will dictate the length of ramp required, if your car has low ground clearance you will also need to take this into consideration. 

How steep should my ramps be?

It entirely depends on the vehicles being loaded, a sports car will require a much gentler gradient than a 4x4, if you are unsure please contact us and we will be able to assist. 

How do I know the capacity I require on a ramp?

When selecting a ramp capacity check the weight of the vehicle, add around 150kg-200kg to allow an extra weight for fuel, operator and any other load added to the vehicle weight. That will be the capacity you will need the ramp to take.

Should I allow extra capacity in the ramps for safety?

No. Our ramps are manufactured and engineered in the EU to European TUV standards, which require us to build in a 200% safety breaking point margin, although the ramps are tested and built on a 200% safety, please note if the ramp is overload this will void warranty.

How do I secure the ramps safely?

There are 4 types of connection for our loading ramps suitable for different vehicles & applications. Rest on connection with a drilled hole for the safety pin tends to be the standard as they work in most situations. For our car ramps we would recommend either the rest on connection with a drilled hole for the safety pin or the hook connection. The rest on connection is the standard as they work in most situations. Our connection options can be viewed here. 

car ramps

Mobile Yard Ramp FAQ's

What is a mobile yard ramp?

A mobile yard ramp is used to load and unload shipping containers without the use of a permanent docking bay. The ramp is placed and the back of the vehicle, allowing machines such as forklifts and plant machinery to gain access into the container to unload and load containers quickly and safely. 

What is the capacity of a yard ramp?

We provide forklifts with capacities up to 15,000kg, if you require a higher capacity please let us know as these can be customised to your specifications.

Are the mobile yard ramps customisable?

Yes, the ramp can be customised in terms of length, width and capacity. The ramp can also be produced with handrails for increased safety.

Are the ramps certified?

Yes, our yard ramps are CE marked and produced in Europe.

How easy is it to put the mobile yard ramp into place?

The mobile docking yard ramp can easily be moved as it has a fixed swivel clamp which allows a forklift to easily move the ramp into place. The ramp is provided on rubber tyres which helps allow it to turn with ease. The height of the ramp can easily be adjusted using the hydraulic pump. 

What are the mobile yards made from?

The ramps are produced from steel, they have a mesh anti-slip surface to ensure optimal grip and safety. The ramps are suitable to be used in all weathers. 

Are the ramps safe to use?

Yes, the ramps are CE marked. The yard ramp is produced with a mesh surface to provide extra grip, the ramps are customisable and can include handrails to increase safety further if required. Steel safety chains are also provided, which include large hooks, to allow the ramp to be secured in place during use. The ramps are provided with a full user manual along with a 1 year warranty. 

 

Truck and Van Ramps FAQ's

How long should the ramp be?

For Truck & Van Ramps Health & Safety recommend that no gradient greater than 30% (16.5 degrees) should be used. Furthermore, no TUV Certified Ramp is designed to exceed this gradient. To calculate your gradient simply multiply the bed height of your vehicle by 3.3 to give the optimum length. If loading long/heavy cases or pallet trucks, we recommend much longer.

Do the ramps have a minimum load height?

No but we don’t advise to use the ramps lower than 100mm of the stated max load height as the foot end will not sit flat on the ground. For example, if the ramp has a max load height of 900mm do not use lower than 800mm.

For custom solutions, please contact our ramp specialists.

Can the ramps be used over the max load height?

No, the ramp will be too steep. Using the ramp above it’s recommended load height may cause accident, injury or death and will invalidate the warranty.

Should I allow extra capacity in the ramps for safety?

No. Our ramps are manufacturer and engineered to European TUV standards, which require us to build in a 200% safety margin. please note if ramp is overloaded this will void warranty.

Can I use a winch to assist loading equipment?

Winches fundamentally alter the normal weight distribution when loading machines and equipment. Stated weight limits are dramatically reduced when using a winch. Winches can be used but great care and attention must be taken, please speak with our sales advisers for help specifying ramps. The most important thing is to keep the rope of winch parallel with the ramp. If you intend to use a winch please make this clear to your sales adviser before purchasing.

How does the ramp connect to the vehicle?

All of our truck & van ramps use a rest on connection which rests onto the floor of the vehicle. The Premium van ramps & the truck ramp range come supplied with a locating pin which can be used to anchor the ramp if a matching hole can be driven into the floor of the vehicle.

How grippy is the surface?

As grippy as we can make it without causing damage to tyres or excessive wear to the surface. Our ranges have light serrations cut across the width which is suitable for dry, clean conditions. If you plan to use in wet or muddy conditions further grip might need to be added such as grip tape or rubber covering.

Can the ramps be customised? 

We can customise the ramps to your required length and width, we also have alternative connection types available and can built the ramps for various capacities. The lead time on built to order items is normally 3-4 weeks. 

What is the difference between the premium van ramps and the economy ramps?

Our premium ramps are TUV certified and produced in Italy, they can be customised if required. The entry onto the ramp for the premium version is slightly smoother than the economy version. The premium version holds a higher capacity (1,000kg+) than the economy version. 

Fixed Folding Van Ramps FAQ's

How do I find the correct size of ramp for my van?

With so many models and variations we ask that you complete our measurements document so that we can recommend the best suited model for your application. It is imperative to check these measurements as the wrong size of ramp will not fit the van. See here our measurements guide which we ask you to complete and return via email.

What are the benefits of the mesh surface?

The mesh surface is slightly lighter, a bit more grip & in wet conditions, allows water to run through the surface rather than down it. The mesh also leaves some visibility through rear windows. Mesh surface is currently only available up to 400kg.

What is the pivoting/twisty System?

The pivoting system is a hinge on the bottom corner of the ramp which allows the system to be turned 90 degrees in or out of the van making for quick access the loading bay without the need to deploy the full ramp.

Can I install the ramp myself?

Yes, our ramps can be fitted by any competent DIYer see our fitting guide here.

Can the ramps be easily removed?

As standard it will mean removing bolts and brackets which could take some time. If the ramp is to be regularly removed then we suggest you purchase our quick release system which allows the base plate to be unclipped in under a minute leaving just the brackets on the floor. The quick release system is NOT available for ramps with the twisty system.

Can the ramps be secured when vehicle is moving?

Yes, we will supply a pair of straps to secure the ramp for when the vehicle is on movement.

Not using the straps will decrease the life usage of the ramp, cause damages and will void the factory warranty.

Can the ramp be customised if I need a specific length, width or capacity?

Der Rampen Shop can manufacture folding van ramps to specific needs, please contact a sales advisor for more information.

What if I need spare parts?

The Ramp People keep various spare parts in stock for a next day delivery.

Are the folding van ramps suitable for loading wheelchairs?

Yes, they are suitable however we recommend the mesh surface ramps for loading wheelchairs. 

Folding Van Ramp

Motorcycle & Folding Loading Ramps FAQ's

How do they connect to the vehicle?

The ramps use a rest on connection which is either red prongs or a solid lip (depending on model) which rests onto the surface you are loading onto. Straps come supplied which can be used to secure the ramps in place.

Are they lightweight?

Yes, all our folding ramps are under 20kg in weight & a pair splits up the weight so that you only need to move one ramp at a time.

Can I buy a single ramp?

Yes, singles can be viewed under motorcycle ramps on our website.

How grippy is the surface?

As grippy as we can make it without causing damage to tyres or excessive wear to the surface. We have a variety of surfaces available, including a mesh surface and cut-out grip system to allow you to choose a suitable surface for your requirements. If you plan to use in very wet or muddy conditions further grip might need to be added such as grip tape or rubber covering.

Which length ramp should I buy? 

You need to check your load height (from the ground to where the ramp will rest) as this affects the length of ramp required. All of our products note the maximum load height for the ramp in question. You also need to consider the maximum weight you wish to load. 

How wide are the motorcycle ramps? 

We have various widths available from 230mm - 440mm. 

Why are the ramps curved?

The ramps are curved to improve ground clearance. 

What other items can be loaded on these ramps?

Our motorcycle ramps are regularly used to load quad bikes, ride on lawnmowers, garden machinery and ATVS. 

motorbike motorcycle ramp

Cable Protectors FAQ's

Why are there so many different types?

We offer a complete range of cable protectors from pedestrian cable covers to heavy duty vehicle cable protectors so that we are ready to assist with any application. We also provide kerb ramps with channels underneath so cables can run below them. 

What is the difference between a cable cover & a cable protector?

A cable cover is designed to drop over wires whereas cable protectors encase cables completely. Cable covers offer a swift installation/removal. Cable protectors offer a more secure protection.

Do you have cable protectors suitable for vehicles to cross?

Yes, we have options with capacities ranging from 2000kg to 15,000kg (per section) but please be aware as our 2-channel option is 105mm high it is only suitable for HGV’s & other vehicles with plenty of ground clearance.

How can I check the channel size?

All channel dimensions are listed in our product specification pages, if you are at all unsure or cannot find a suitable option please get in touch.

What are they made of?

The majority of our range is rubber although there are some polyurethane options. This means our products are heavy duty and hard wearing.

Can they be fixed in place?

We do not recommend fixing our products as they are designed to be portable. Some customers have used adhesive tapes or fixings but the product does not come supplied with fixing holes or fixings. The Adam Hall Defender® however come with fixing holes by standard. The fixings will not be supplied with the order.

Can cable protectors be used in a warehouse?

Yes, however please ensure you select one of our cable protectors that are suitable to be used with forklift/trollies, for example within the Adam Hall Defender® range there are cable protectors which are suitable for items with low ground clearance.

Can cable protectors be connected together? 

Yes, our heavy duty cable protectors and cable covers are interlocking so you can create your required length. Our lightweight cable protectors are available in lengths up to 9m, as they are lightweight PVC you can cut these to your required size when needed. The Checkers® range and the Adam Hall Defender® range can be each connected with each other.

Rubber Threshold Ramps FAQ's

What is a threshold ramp? 

Threshold ramps are provided as simple ramp solutions to allow the user to navigate through doorways, over curbs and other low heights. They are provided at a safe gradient to allow manual and electric wheelchairs to go up the threshold. 

What height variations are there?

We supply from 4mm to 100mm high in our rubber range with many sizes in between suitable for almost any doorway or step.

How do you measure the height of wheelchair ramp you need? 

Simply use a tape measure to identify the total vertical height of the threshold and select the ramp which is this height. 

What is the difference between the two rubber threshold ramps ranges?

The rubber threshold ramps up to 70mm high are designed for lower heights & have a 1:10 gradient ratio. The rubber threshold ramps up to 100mm high are slightly steeper, higher & have sloped edges.

What widths are available?

We offer widths between 900mm, 1000mm and 1105mm. You can also cut to size if they need to be narrower.

How portable are they?

Being solid rubber they are quite heavy so should ideally be left in place semi-permanently. The weight helps to keep them in place.They are waterproof so you can leave these outside. 

Are they suitable for electric wheelchairs and mobility scooters?

Yes, they are due to a gentle gradient.

Can they be customised?

No, but they can be easily cut at home using a saw or knife, please only cut these widthways so you do not affect the gradient of the ramp. 

Pallet Truck Ramps FAQ's

Why are they so long for such low heights?

Pallet trucks are not designed to operate on slopes due to a long low wheelbase. Because of this a very gentle gradient is required especially when moving heavy weights.

Can they be used on steps?

Yes, our pallet truck ramps can be used in other areas where low obstacles need to be overcome.

Should I allow extra capacity in the ramps for safety?

No. Our ramps are manufacturer and engineered to European TUV standards, which require us to build in a 200% safety margin.

Can I use a winch to assist loading equipment?

Winches fundamentally alter the normal weight distribution when loading machines and equipment. Stated weight limits are dramatically reduced when using a winch. Winches can be used but great care and attention must be taken, please speak with our sales advisers for help specifying ramps. The most important thing is to keep the rope of winch parallel with the ramp. If you intend to use a winch please make this clear to your sales adviser before purchasing.

 How does the ramp connect to the container?

All of our container ramps use a rest on connection which rests onto the floor of the container. We do have alternative connection types available which can be viewed here, there will be an additional fee of 77,35€ inc. VAT for the alternative connection. 

How grippy is the surface?

As grippy as we can make it without causing damage to tyres or excessive wear to the surface. Our pallet truck ramps have light serrations cut across the width which is suitable for dry, clean conditions. If you plan to use in wet or muddy conditions further grip might need to be added such as grip tape or rubber covering.

What if I need a specific length or width?

Der Rampen Shop can manufacture to almost any width or length required. 

Wheelchair Channel Ramps FAQ's

What advantages and disadvantages does a pair of ramps have?

They are much lighter to lift as only one needs to be picked up at a time but the width does need to be set for each wheelchair wheel. 

Are they suitable for electric wheelchairs and mobility scooters?

No, due to the high upstand safety edges these are not suitable for electric wheelchairs or mobility scooters.

Are they easy to store?

As the ramps are telescopic they can go to a very compact size for storage.

What lengths are available?

We offer 12200mm to 3650mm length options in several different styles.

What variations are available?

The majority of our ranges are telescopic (with and without black grip tape) but we do also offer rigid and folding options as well as extra wide channel ramps. If you wish to use the ramps at alternative lengths, please view our Economy Telescopic Channel Ramps 1220mm to 3650mm, these can be clipped to match your required length. 

Can the ramps be used in between the minimum and maximum lengths?

The ramps can be used at any length between the minimum and maximum lengths as the weight on the ramps causes them to flex slightly locking them at the required size.

What are combination channel ramps? 

The combination channels can be used to go up and over a threshold as they have a hinge. They also can be used as straight ramps to go up a set of steps. 

How do they stay on the step?

The ramps curve at the end, this allows them to simply rest on the step. 

How easy is to use line up the wheelchairs wheels with the channels?

The first few times of using the ramps it will take a few attempts to position correctly, but after a few uses it becomes easier to judge where the ramps need to be placed. Some customers Mark on the floor or door frame with chalk to make it immediately apparent where each ramp needs to be placed.

Channel Ramps Channel Ramps Channel Ramps

Wheelchair Bridge Ramps FAQ's

Are they suitable for electric wheelchairs & mobility scooters?

We do not recommend bridge ramps for electric wheelchairs or mobility scooters as they tend to have very low ground clearance, a long wheelbase which means as they cross the underside catches they can become stuck on the ramp. If you have a mobility scooter or electric wheelchair we would recommend a rubber threshold ramp on either side of the door.

How wide are they?

Most of our bridge ramps are about 70cm wide so that they are narrow enough to fit in door frames but still wide enough for a manual wheelchair.

Can they be used on uneven rises?

We recommend bridge ramps for even heights otherwise one ramp will be steeper than the other which is not comfortable to cross and could cause the ramp to move during use.

For this situation you can use either fibreglass threshold ramp or drive in ramp

How can I ensure the ramp does not come into contact with the threshold?  

The fibreglass threshold ramp and the bridge threshold ramp has legs/supports to prevent the ramp and preventing it touching the threshold. Other bridge ramps do flex and may come into contact with the threshold, we would recommend checking your doorway is suitable prior to use.

Can I leave the ramp in place?

As the ramp is placed in the doorway, you will be unable to close the door while the ramp is in place. Our folding drive in ramps can be left in place as it has a fold-up tail which can be moved to allow the door to close. 

Bridge Threshold Ramp Bridge Threshold Ramp Bridge Threshold Ramp

Container Ramps FAQ's

How long should the ramp be?

For plant ramps Health & Safety we recommend that no gradient greater than 30% (16.5 degrees) should be used. Furthermore, no TÜV Certified Ramp is designed to exceed this gradient. To calculate your gradient simply measure the height from ground level to the loading deck & multiply this by 3.3 to give the optimum length of ramp.

Plant Ramp Length Calculation

Should I allow extra capacity in the ramps for safety?

No. Our ramps are manufacturer and engineered to European TUV standards, which require us to build in a 200% safety. When calculating which capacity you require you must factor in the weight of the machine, the load if any, the operator, fuel/oil and attachments. Please note if you exceed the stated capacity the warranty is invalidated.

How durable are aluminium ramps compared to steel?

If the ramps are used sensibly, there is no reason why aluminium ramps should not last as long as steel, and much longer than steel ramps with wooden inserts.

Do the ramps have a minimum load height?

Yes, please check specs of each ramp.

What is the benefit of the rubber container ramp? 

The rubber container ramp has a capacity of 10,000kg and is provided in modular pieces to allow this to easily put in place and removed by one person. 

Why do these need to be used at a specific load height?

The foot of the ramp is cut for the specific load height, when used at the incorrect load height the weight will not be able to take the required weight and the warranty will be void. 

What is the benefit of a wedge ramp?

These can be customised to match your required height. They are perfect for loading pallet trucks to heights up to 120mm and can hold capacities up to 2920kg.

Can the aluminium container ramps be customised?

Yes, our aluminium ramps can be customised in terms of width, length, connection and capacity to meet your requirements. 

container ramps

Folding Wheelchair Ramps FAQ's

How wide is a wheelchair ramp?

Wheelchair ramps are provided in various widths, our standard folding wheelchair ramp is 720mm wide. The key is to check the width of your doorway to ensure the ramp will fit in the required door. In addition the width of the wheelchair needs to be checked to ensure the wheelchair will fit on the chosen ramp.

Can I rent a wheelchair ramp?

With wheelchair ramps available from very low costs, we do not rent wheelchair ramps. In addition, all of our ramps are provided with a 1 year warranty, this can only be provided on new ramps as we can ensure they are provided to you in perfect condition.

What is a portable wheelchair ramp?

Portable wheelchair ramps are designed to be used on a temporary basis. They are often folding or telescopic for ease of storage. These ramps can be great for those who wish to travel or use the ramps on a variety of steps/thresholds.

How long does a wheelchair ramp need to be and what is the maximum slope of a ramp?

We recommend a minimum of a 1:6 gradient for manual wheelchair, 1:8 gradient for electric wheelchairs and scooters. A 1:12 gradient is recommended for modular ramp systems. 

Are portable wheelchairs safe? 

As long as portable ramps are used within the capacity stated for the ramp, for their recommended purpose (loading wheelchairs) and within the recommended load height they are safe to use. 

How much does it cost to build a wheelchair ramp? 

Portable wheelchair ramps, including rubber threshold ramps which can be left in place, start from 14,28€ inc. VAT upwards. 

What is a suitcase ramp?

A suitcase ramp is a folding portable wheelchair ramp which folds up as if it were a suitcase to allow the user to easily carry the ramp and use in alternative locations. 

Are wheelchair ramps suitable for manual and electric wheelchairs? 

Our standard folding ramps and our rubber threshold ramps are suitable for manual wheelchairs, electric wheelchairs and scooters. Channel ramps are only suitable for manual wheelchairs. If you are unsure please check the symbols on the product page which state which types of wheelchairs they are suitable for you, alternatively simply ask one of our advisers 

How much does an aluminium ramp cost? 

Our aluminium wheelchair ramps start at 71,40€ inc. VAT. 

wheelchair ramps

Speed Bumps FAQ 's

What is the purpose of speed bumps?

Speed bumps are designed to slow down vehicles and increase safety within pedestrian zones.

What regulations are in place regarding speed bumps? 

There are no clear legal regulations for installing speed bumps in Germany. Please check with your own countries regulations before purchase. For installation in public places we would recommend the deployment of our 50mm high speed bumps. Thus it is guaranteed, that vehicles with a low ground clearance, which are allowed according to the German Road and Traffic Regulations (StVO), can cross over the speed bumps without any problems. We also recommend the usage of the German traffic signs VKZ "uneben road" and VKZ 274 "permitted top speed" in suitable distance before the speed bumps. Once you show the speed bumps and top speed in advance, it will help reduce the noise and prevent any damages on the vehicles passing, which might be passing otherwise too fast.

Do speed bumps work?

Speed bumps have been proven to reduce speed in many locations, and make neighbourhoods safety. 

Do speed bumps damage cars?

Cars and vehicles with low ground clearance need to be especially careful when going over speed bumps. As long as the driver is driving at the recommended speed the car should not be damaged by the speed bump. 

How much is a speed bump? 

Our speed bumps start at 88,0€ inc. VAT, this price includes fixings and a free SDS Max drill bit. 

Does Der Rampen Shop install speed bumps?

We do not install speed bumps however we do provide fixings for tarmac and concrete within the price, along with a free drill bit. The speed bumps can easily be installed by a handyman or builder, our speed bump installation guide can be viewed here.

Do you need planning permission for speed bumps? 

You will need to check with the land owner, or local council, prior to installing speed bumps as you will be drilling the fixings into their land. 

What length of speed bump do I need?

This does depend on the road you are installing these on. You will need to measure the width of the road. We recommend leaving some space between the speed bump and pavement to allow pedestrians and cyclists to pass safely. Some opt to have one long speed bump across the road whilst others have 2 speed bumps, one on each side of the road and a gap in the middle, it is personal preference. 

What capacity do the speed bumps take? 

Our heavy duty speed bumps have a capacity of 60,000kg and therefore are recommended for areas with trucks, lorries and vans passing through. If you are installing speed bumps in an area where only cars pass through, our 50mm and 75mm speed bumps will be suitable as these have a 20,000kg capacity. 

What are speed cushions?

Speed cushions are larger than speed bumps in general and are more suitable for larger vehicles, our speed cushions can be viewed here

Are speed bumps safe?

Speed bumps increase safety but you should take measures to ensure the road user is aware of the speed bumps to prevent any damage to the cars. For example, clear signage is required so road users are aware that the road has speed bumps. Reflectors and chevrons on the speed bump help ensure the user is able to see them. 

Speed Bumps

Modular Wheelchair Ramps FAQ's

What is a modular ramp?

Modular wheelchair ramps are ramp systems which are provided in various pieces which connect together to create the required ramp length. These ramps can be provided with or without handrails. They can be created in any length for a variety of heights. Generally the recommended gradient for a modular ramp is 1:12.

What size door is required for wheelchair access? 

It does depend on the size of the wheelchair. Our modular kits are provided in various widths between 900mm -1500mm whilst our portable ramps are provided in sizes from 660mm upwards. 

Can modular ramps be customised? 

Yes. The ramps can be provided in any length. The ramps can include platform(s) as required along with step kits and U-shaped handrails to meet the users needs. We are also able to manufacture specific parts to you requirement. Our team will be happy to assist in providing a quote based on your measurements. 

How easy is it to assemble a modular kit?

A confident DIYer or builder will be able to put together our modular kits. We have an instruction video and guide available for galvanised steel system here and Installation Guide in Image and Word of the FEAL Aluminium modular ramp systems.

How much does a modular wheelchair ramp cost?

This does depend on your requirements, our modular ramps start at 2038,22€ inc. VAT. 

What is the modular ramps made from?

Our modular wheelchair ramps are produced from anodised aluminium or galvanised steel. This ensures these ramps durable and weatherproof. Aluminium however is more lightweight than steel and therefore probably easier to carry.

Are wheelchair ramps required?

In private homes it is up to the individual as to whether they have wheelchair ramp access.

Do the ramps comply with DIN18040 barrier free building regulations?

Our modular ramp kits are designed as portable, temporary solutions and therefore do not need to comply. However, the 1300mm and 1500mm wide of both our ramp systems are compliant with the German DIN 18040 barrier free building regulations.

How long does it take to put the modular kit together?  

It does depend on the persons abilities who is putting the ramp together and the length/size of the system purchased. Please view our modular video and instruction guide for a better understanding of how the systems are put together to allow you to estimate how long it may take you. 

I want a ramp which I can leave in place but I do not want a modular system, is there a solution?

Yes. We have a portable wheelchair ramp with handrails (handrails are optional) which can be secured into place as there is a predrilled hole in the ramp. They can also be used as portable ramps by simply resting these on the step. They are available in 1830mm and 2440mm and are suitable for manual wheelchairs, electric wheelchairs and scooters. 

I require steps and a ramp, is this possible?

Yes, we have various step kit available, for further advice please contact our team so they can work with you to find the best solution based on your requirements. 

Modular Wheelchair Ramp

Modular Wheelchair Ramps FAQ's

Are wheel chocks required?

Wheel chocks are not required in the majority of instances however they can improve safety and reduce the risk of damage to surrounding areas as they prevent accidental movements of vehicles. 

What is the purpose of wheel chocks?

Wheel chocks are used to prevent vehicles, including lorries and planes, rolling accidentally. Wheel chocks are used as an additional safety device, along with the vehicle break. They are often used when a vehicle is parked on a hill, or during loading/unloading. 

How many wheel chocks do you need? 

A minimum of two wheel chocks is required for the wheel chocks to work effectively. For wet or muddy ground conditions, several chocks may be required. 

Where should wheel chocks be placed?

Wheel chocks must be placed downhill. For example, when a car is facing downhill, the chocks would be placed in front of the front wheels. When the car is facing uphill, the chocks should be behind the rear wheel. Aircrafts require usually a wheel chock before and behind the front wheel.

How do chocks work? 

Wheel chocks work by preventing the car from rolling. It is important to ensure tyres are properly inflated to prevent failures occuring. 

Are wheel chocks safe to use? 

Health and safety assessments should be undertaken prior to using wheel chocks. Due to the location wheel chocks are placed in, individuals can be put at risk when moving the wheel chocks and therefore drivers need to be aware not to move until they have been informed it is safe to do so. 

Which wheel chock should I buy? 

You need to consider the size of the vehicle, weight of the vehicle and the ground type when buying a wheel chock. Smaller tyres require smaller chocks. We have a range of wheel chocks suitable for cars and industrial machinery which can be viewed here. In addition we have aviation wheel chocks which are suitable for various aircraft sizes. 

What are wheel chocks made from?

We have a variety of wheel chock which are produced from various materials including rubber and polyurethane. 

Our range of Wheel Chocks can be found here.